This post may contain affiliate links. As an Amazon Associate I earn from qualifying purchases.

You are watching: How to remove polymeric sand from pavers

Polymeric sands have really come along way since their inception in 1999 by Techni Seal. Polymeric sand is a sand formula that is swept into the joints of pavers and natural stone to lock in the product, prevent weed growth and insects, and to provide the final touches of any hardscaping job. The sand remains hard when dry and flexible when wet to allow for it to remain intact if the surface moves whether through frost cycles or traffic. It is what makes it a superior product for the filling of joints.

Over many years, the formula has improved as competition in the space grew and now today we have some pretty incredible polymeric sands on the market. Still the market is not without problems, most of which come from the installation.

The installation of polymeric sand may not get the attention it deserves because it is thought of as being a simple process that can be handed off to anyone. Unfortunately, that is not the case. There is still a lot of involvement in the process and if you miss a step or gloss over the process, you will have a failure on your hands which will cost you time and money.

It is extremely important to read the manufacturer’s instructions before you start the installation. Every manufacturer has a different formula and a different set of instructions. Even between different products in their lineup. That is why it is so important to familiarize yourself with the product that you are used to and to follow the instructions carefully.

There are universal steps to the process of installing polymeric sand, failure signs, and ways in which you can ensure that your polymeric sand installation will run smoothly.

*
*
*
*

The reason why we do this step is to ensure that the sand has made its way to the bottom of the joint. The large grains of the sand will lodge themselves part of the way down the joint and will trap the smaller particles near the top making it look like the joint is filled. Using the plate compactor, you are able to make sure that the vibration causes all of the grains to make their way to the bottom of the joint. If you can make at least one pass, overlapping your passes by at least 1/3 of the width of the plate compactor, you will provide enough consolidation of the polymeric sand.

Doing this also levels out the material which reduces the high and low points in your installation, making it look smooth and complete. You will also notice that the material has locked itself together and does not move when you walk over it now.


Sweeping and Blowing

After this compaction process, you will be left with some sand and dust residue on the surface of the stones. You will also notice that your joints need a little bit more topping up in most of the areas. You can now take the time to sweep in some more sand to the joints that need it. Now, some manufacturers claim their sand to be haze free and it does not require a blower to remove this dust before watering. What this means is that when it is watered, there is no residue that solidifies itself to the surface of the stone requiring a cleaner to remove it off. In my experience, this has not been the case and you should always remove any residue from the surface using a blower before moving on to the next step.


Watering

Watering should always start from the bottom of the slope. This ensures that you are activating the sand that you want to activate by getting to the bottom of the joint without having the water running down the slope activating only the surface of the sand if you were to start at the top of the slope. You should focus on a certain area for specific amount of time on the shower setting before continuing on to another area of the project. This is where referring to the manufacturer’s instruction is important. You should be looking for what setting to have your hose on, how long you should be watering the sand for, and how much square feet at a time you should be activating.

Blowing

Any excess sand on the surface of the stones can now be blown off with your leaf blower to make sure that they do not adhere themselves to the surface of your stones.

Polymeric Sand Problems

Polymeric sand installations are not without their problems. Following the instructions is the first step to ensuring there is no failure. However, mistakes happen and there are problems with some installations. Let’s get into some of the problems and the solutions to those problems.

Polymeric Sand Not Hardening

The number one problem that occurs with the installation of polymeric sand is that it does not set. What this looks like is the sand not hardening. A simple test for this is sticking a screwdriver into it. If it is able to penetrate the sand, then there is a problem. Typically this occurs because there was a rainfall shortly after the installation which caused the sand not to set, the sand was watered for too long, or there is not proper drainage in the base.

If the problem is caused by the base, then there is a bigger problem at hand. The solution for this would be to remove the polymeric sand, install a jointing sand, and use a joint stabilizer on the sand as an alternative to the polymeric sand. If you believe it was because the sand was too saturated or there was a rainfall before the sand set, then you can scrape out the sand and try reinstalling the polymeric sand.

Polymeric Sand Crust

If there is a crust forming on the surface of the sand, typically this means that the sand was filled too high or the sand was not watered enough. If the sand was filled too high in the initial installation, the sand will continuously be worn and eroded away. If the sand was not watered enough, then the surface was able to solidify but everything below it would remain fairly loose causing the top layer to crust and peel away. The solution to this problem is unfortunately removing the sand and replacing it much like what was described above and we will get into the process further below.

Polymeric Sand Haze

Polymeric sand haze is a dust haze that hardens to the surface of the pavers. This is caused by skipping the blowing step in the process of installation. What is left behind is the hardened dust on the surface of the pavers that needs to be removed. The process of polymeric sand haze removal involves using a saturated chemical clean the surface of the pavers and remove the haze. Click this link if you want to learn more about the process of cleaning pavers.

Polymeric Sand on Pavers

Knowing how to remove polymeric sand from pavers is not difficult, just time consuming and tedious. Warm to hot water actually reactivates the polymers within the sand and allows you to scrub or wash away the sand that is stuck to the surface of the pavers. If you have a small area like a corner where sand built up and hardened, you can simply boil some water and use that to pour on top of the affected areas and wash away the sand. If you have a larger area, then you will want to have a hot water pressure washer with an oscillating head to avoid wearing down the surface of the pavers to remove the polymeric sand from the surface.

How to Remove Polymeric Sand

Whether you are replacing and freshening up your polymeric sand or you are fixing a problem, polymeric sand removal may be required. Removing polymeric sand from pavers is not a fun process. You can try to use a hot pressure washer to remove the sand, but you may be left with some sand remaining in the joint. Regardless, you are going to have to scrape out the sand of the joints and use a shop vac or blower to remove this scraped out sand. If you are using a pressure washer, make sure that you have an oscillating head on it.

When removing sand, you want to make sure that you have at least 1″ in depth to replace the polymeric sand so that you have a strong bond. If you are removing just a portion of the sand in your entire project, it is best to remove beyond the problem area to ensure a strong bond.

What is the Best Polymeric Sand

The best polymeric sand depends entirely on the application. There are industry leaders in polymeric sands on the market that you should look for and you will likely find a product that you are used to installing over time. It is also important to choose the polymeric sand for your application.

If you are installing polymeric sand for flagstone that typically has larger joints or any product with joints larger than 1″, you are going to want to pay more money for the polymeric sand that is installed for wider joints. Most pavers will be fine with the regular polymeric sand option, unless installed on top of concrete as an overlay. In this case, there will be a specific polymeric sand for this application.

Polymeric Sand Alternative

There is an alternative to polymeric sand on the market that can be used. Azpects makes a product called EASYJoint which is installed wet and is air cured. This allows you to install it early or late in the season when polymeric sand is a little bit more difficult to install. It also allows water to permeate through, whereas polymeric sand only lets a small percentage of water to pass through. Since this product allows such a large amount of water to pass through, it is best used in applications where an open graded base is installed that allows water to pass through.

See more: How Many Factors Does 144 Have? ? Factors Of 144

There are other alternatives on the market to polymeric sand and the formula is always in the process of refining itself to be easier to install for every user. However, we have had the most success with polymeric sand in our installations and will be using EASYJoint when necessary and on certain applications.